Shield Warrior vs Dragon Flame — Monitor Buddy

The Ice Blue Frost Skeleton Dragon breaks free of the abyss and its destroying fire comes flooding in. As others scatter and the homeland teeters on the edge of annihilation, he pulls on armour that's gathered dust for years, lifts a greatshield worn by time, draws a sword still keen enough to bite, and stands alone in the path of the dragon's breath. Every time you switch your PC on, the dragonfire ignites in sync — that epic standoff bursts to life, and you get the fantastical thrill of a dragon bearing down on your desk.

This is the second kit in Monitor Wars — an expansion set with a shield-bearing warrior, plus a brand-new dragon flame. It works with either dragon in the series, the Ice Blue Frost Skeleton Dragon or the Ember Hell Flame Scale Dragon. One kit, two dragons.

Sizes have to match your dragon: 10 / 20 / 28 cm, each one paired with the dragon of the same size. This set is much quicker to print than a dragon

Already printed the Ice Blue Frost Skeleton Dragon or the Ember Hell Flame Scale Dragon? Then don't reprint it — just print the warrior and the new flame, and put them together for the full standoff. Haven't printed a dragon yet? I'd print both at the same time; the moment it lights up, it looks incredible. Printing the warrior on his own works too, though without the dragon flame it just isn't the same scene.

Supports are already set up, so it's ready to print as-is. I've optimised them as much as I could; almost all contact surfaces are sloped angles, and both PLA and PETG release cleanly in my testing.

The warrior goes wherever your dragon goes — whichever corner it's in, that's where he stands. By default he takes the upper-right corner of your monitor. Moving to the other side? Mirror both pieces together, or they won't line up.

The lighting works the same as the other two kits — one 5V USB COB LED strip (1 mm, the thin wire kind) is all it takes. Plug it into the USB port on the back of your monitor or straight into your PC; it lights up with your machine, no switch needed. In China, search it on Pinduoduo, about ¥10. Overseas, search the same thing on Amazon, Seeed Studio, or AliExpress. No LED strip on hand? Print it anyway — the light is what brings it to life, but you can always add it later.

I've put a lot of work into this one, so if you print it — I'd really love to see your make photo and a rating!

Print it on its own, or pair it with the Ice Blue Frost Skeleton Dragon or the Ember Hell Flame Scale Dragon. On one side, an abyss of devouring flame; on the other, a refusal to give up a single inch. Print the dragon too and set them side by side — that final standoff between dragonfire and shield plays out right on top of your screen.

Follow me if you want to catch new kits as they drop.

Tap the title below to jump straight over.

Ice Blue Frost Skeleton Dragon Breath Lamp on Boot — Monitor Buddy

Ember Hell Flame Scale Dragon Breath Lamp on Boot — Monitor Buddy

————以下为中文版简介————

深渊的巨龙挣脱禁锢，毁灭的龙焰奔涌而来。当他人四散逃亡、家园濒临覆灭之际，他穿上了尘封已久的盔甲，拿起历经岁月的巨盾，抽出依旧锋利的神剑，孤身挡在龙息面前。

每一次开机瞬间，龙焰都能同步点燃这史诗般的对战场景，感受巨龙来袭的奇幻氛围感。

这是《显示器上的战争》系列的第二作，一套拓展组件：一位持盾的战士，加上一版全新造型的龙焰。它能搭配系列里两条各具特色的巨龙：冰蓝霜骸骨龙和 烬狱焚鳞魔龙，非常方便。

这个套件要和你打印的龙对应：10 / 20 / 28cm，比如你打印了20cm的龙，就打对应大小的重盾战士套件。这一套比打印龙本身快得多

如果你已经打过冰蓝霜骸骨龙和 烬狱焚鳞魔龙的话——不用重打，直接打这个战士和新版龙焰就行，摆上去就是完整的对峙场面。还没打过龙的话，建议龙和战士一起打，装好点亮那一刻效果炸裂的好。只想打战士一个人也行，只是没有龙焰的话，这一幕就少了不少味道。

支撑已经设置好了，可直接一键打印。支撑已经尽可能优化过，绝大部分都是斜面，实测 PLA 和 PETG 都能完整拆除。

战士跟着你的龙安装就行——龙在哪边，他就挡在哪边，默认在显示器右上角。要换边的话记得两件一起镜像，不然对不上位。

灯的部分和另外两作一样，一根 5V 1mm 360度 COB 灯带就够。插显示器背后的 USB 口，或者插主机上都行，跟着电脑一起亮。国内拼多多搜一下 10 块钱左右，海外的朋友在 Amazon、Seeed Studio 或 AliExpress 搜同样的关键词。手头没有灯带也照样能打——灯是让它活起来的那一笔，什么时候想加都行。

这是我非常用心做的模型，期待你的返图和评分！！！！

本模型既可单独打印把玩，也可搭配《冰蓝霜骸骨龙》、《烬狱焚鳞魔龙》联动使用。一边是无尽深渊的毁灭燎原，一边是寸土不让的执念坚守——把龙也打出来摆在一起，龙焰与坚盾的终极对峙就在你的屏幕顶端上演。